วันอังคารที่ 29 มีนาคม พ.ศ. 2559

TPIC6B595 ควบคุม LED









โจทย์ เมื่อกด สวิทย์ ให้ ไฟติดตามตำแหน่งที่กดสวิตย์ ปล่อยแล้วดับ

/*

Shift Register Example

for TPIC6B595 shift register by Jens C Brynildsen

This sketch turns reads serial input and uses it to set the pins
of a TPIC6B595 shift register.

Hardware:
* TPIC6B595 shift register attached to pins 7, 8, 11 and 12 of the Arduino,
as detailed below.
* LEDs attached to each of the outputs of the shift register

Based on the example created 23 Mar 2010 by Tom Igoe

*/

//Pin to clear the register
const int clearPin = 13;
//Pin connected to latch pin (RCK) of TPIC6B595
const int latchPin = 10;
//Pin connected to clock pin (SRCK) of TPIC6B595
const int clockPin = 12;
////Pin connected to Data in (SER IN) of TPIC6B595
const int dataPin = 11;
//Pin input switch
int in1 = 2;
int in2 = 3;
int in3 = 4;
int in4 = 5;
int in5 = 6;
int in6 = 7;
int in7 = 8;
int in8 = 9;
int k =0;
int counter = 0;
int numLedsInUse = 8;

void setup() {
 //set pins to output because they are addressed in the main loop
 pinMode(clearPin, OUTPUT);
 pinMode(latchPin, OUTPUT);
 pinMode(dataPin, OUTPUT);  
 pinMode(clockPin, OUTPUT);
 pinMode(9, INPUT_PULLUP);
 pinMode(8, INPUT_PULLUP);
 pinMode(7, INPUT_PULLUP);
 pinMode(6, INPUT_PULLUP);
 pinMode(5, INPUT_PULLUP);
 pinMode(4, INPUT_PULLUP); 
 pinMode(3, INPUT_PULLUP);
 pinMode(2, INPUT_PULLUP);
 Serial.begin(9600);
 Serial.println("*");
 // Always start by setting SRCLR high
digitalWrite( clearPin, LOW);

 // delay a little and then set 
 delay(100);
}

void loop() {
// // Display LED's running
// if( counter >= (numLedsInUse-1) ){
//   counter = 0;
// } else {
//   counter++;
// }
// 
// write to the shift register with the correct bit set high:

  for(int i=2;i<=9;i++){
      if(digitalRead(i) == LOW && k == 0){
        registerWrite(i-2, HIGH);
        k = 1;
      }
      if(digitalRead(i) == HIGH && k == 1){
        registerWrite(i-2, LOW);
        k = 0;
      }
  }
}

// This method sends bits to the shift register:

void registerWrite(int whichPin, int whichState) {
 Serial.println(whichPin);
   
 // the bits you want to send
 byte bitsToSend = 0;
 // write number as bits
 bitWrite(bitsToSend, whichPin, whichState);

 // turn off the output so the pins don't light up
 // while you're shifting bits:
 digitalWrite(latchPin, LOW);
 Serial.println(bitsToSend);
 Serial.println("_");
 // shift the bits out
 shiftOut(dataPin, clockPin, MSBFIRST, bitsToSend);

 // turn on the output so the LEDs can light up:
 digitalWrite(latchPin, HIGH);
}